Why is my Dewalt nail gun not shooting nails? (2023)

First, you should check to make sure that the gun is firmly loaded with the correct nails and they are being loaded into the magazine properly. Next, check to make sure that the compressor is providing enough air pressure to the gun by setting the pressure regulator and gauging performance.

Minecraft - How To Download & I...

Minecraft - How To Download & Install Minimap Mod (Xaero’s Minimap)

Additionally, the hose connected to the gun may be clogged or blocked, so check to see if the hose is securely connected and blow compressed air through it if necessary. Finally, the safety interlock mechanism on the gun might be released, preventing it from firing, so double check to make sure that is securely engaged.

Why is my nail gun misfiring?

It is possible that your nail gun is misfiring because of a variety of issues. First, it could be caused by a worn or broken piston driver. If a piston driver is either cracked or shows signs of wear, it can cause the nail gun to misfire.

Another possible cause is if the nails being used are either too long or too short for the tool. If nails are too short, they will not be able to reach the end of the barrel to be propelled out. If the nails are too long, they can create too much tension for the piston driver, and cause it to misfire.

Another potential cause is a problem with the air compressor. If the air supply is not providing enough pressure, it can reduce the ability of the nail gun to fire nails properly. Lastly, it is possible that the nails are blocked, bent or jammed within the gun, causing it to misfire.

To fix the issue, first check to make sure the piston driver is not cracked or worn, then make sure the nails are the right size and are not blocked or jammed in the gun, and then make sure the air compressor is providing enough air pressure.

How do you adjust the pressure on a nail gun?

(Video) How To Fix a Dewalt Framing Nailer: QUICK & EASY!

To adjust the pressure on a nail gun, you’ll need to fir st locate the pressure adjustment knob. This is typically located either at the front or on the side of the gun, or in some cases, it may be a separate device that is plugged in and attached to the gun.

Once you have located the pressure adjustment knob, turn it in the desired direction to adjust the pressure. Be careful to make small adjustments, as it’s easy to over-adjust and cause damage to the gun or surrounding environment.

If you are unsure what kind of adjustment to make, consult with the gun’s manual or the product specifications, or ask a professional for guidance. Once you’ve made your adjustment, test the gun on scrap material or a piece of plywood to ensure everything is working correctly.

If not, proceed to make further adjustments as needed.

What can go wrong with a nail gun?

When using a nail gun, there are several potential risks that can occur if proper safety measures are not taken. The most common accidents include nail gun kickback, nail misfires, and nail gun jams.

Nail gun kickback happens when the nail is fired, but it does not penetrate the material and instead ricochets back. This can cause serious injuries, such as nail embedded in the skin, lacerations, and eye injuries.

It is important to inspect the area and clear away any debris before use to reduce the chances of this occurring.

Another potential risk with a nail gun is a nail misfire. This happens when the nail is not properly seated in the gun and is fired without entering the material. As with kickback, this can lead to serious injuries and it is important to inspect the nail before use and ensure that it is securely locked into place.

Finally, a nail gun can jam if there is a blockage in the air or fuel delivery system. If a jam does occur, it is important to clear the obstruction and/or have the nail gun serviced by a professional before continuing use.

Overall, when using a nail gun, it is important to take all proper safety precautions, such as wearing eye protection, following operating instructions, and maintaining the gun. Taking these steps can help to reduce the chances of accidents and injuries.

How long do nail guns last?

Nail guns, also known as nailers, can last anywhere from 3-7 years depending on how often it is used and how well it is cared for. Depending on the type of nail gun and the manufacturer, you can get even more out of your nail gun with proper cleaning and maintenance.

If your nail gun is used regularly and stored properly, it should last longer. To ensure your nail gun will last longer, make sure you read the user’s manual that came with the nail gun and follow the instructions.

Clean and lubricate the nail gun regularly and use the right lubricants or fuel in the case of cordless or gas-powered nail guns. If you notice any parts of the nail gun wearing out, replace them right away.

Regularly checking the condition of the nail gun and switching out consumable parts like O-rings or nozzles is important to keeping a nail gun functioning properly.

How do you lubricate a nail gun?

(Video) Dewalt Framing Nailer Jammed Won't Fire Cordless 20V DCN692B

Lubricating a nail gun is important in order to keep it functioning properly, and should be done on a regular basis. To lubricate your nail gun, there are a few simple steps that you can follow.

First, remove any nails from the gun and then disconnect it from its air supply. If there’s any remaining debris in the chamber, you should remove it before proceeding.

Second, apply a few drops of oil to each of the nailer’s moving parts (including the trigger valve, the cylinder head, and the seal cups) and carefully wipe away any excess oil. Make sure to avoid over-oiling the nailer as too much oil can cause it to malfunction.

Third, press the trigger several times to ensure that the oil is properly distributed. Finally, you can reattach the air supply and add nails back into the chamber. By following these steps, you can ensure that your nail gun is properly lubricated.

What are common hazards when working with pneumatic nail guns OSHA?

Common hazards when working with pneumatic nail guns OSHA include puncture hazards, tripping hazards, eye and respiratory hazards, and hearing hazards.

Puncture Hazards: Nail guns that use compressed air to drive nails into objects can cause puncture injuries if users are careless when using the tool or if the tool is stored improperly. These injuries can range from minor to severe, and in some cases may require medical attention.

Tripping Hazards: Tripping hazards associated with pneumatic nail guns are generally in the form of nails that are driven into objects or surfaces that can pose a risk of tripping, such as an uneven floor or wall.

Eye and Respiratory Hazards: One of the primary hazards associated with pneumatic nail guns is dust and debris that is created when a nail is shot. This debris can cause eye irritations, stinging, coughing, and in some cases, respiratory issues.

It is important to wear protective equipment, such as safety glasses and a dust mask, when operating a pneumatic nail gun.

Hearing Hazards: The loud noise associated with a pneumatic nail gun can cause hearing damage if the user is not wearing appropriate hearing protection. Wearing earplugs or earmuffs is highly recommended when operating this tool.

Additionally, make sure to alert any bystanders to the potential noise risk.

How can you prevent nail gun injuries?

First, it is important to evaluate the workplace and use safety guards, push-blocker devices, or contact-trip triggers that can help reduce potential nail gun injuries. Additionally, it is important to ensure that all operators of the nail guns have received the proper training and certification on proper use and safety precautions.

This should include proper use and protective gear, such as safety goggles, dust masks, and hearing protection. Furthermore, employers should make sure that the nail guns are regularly inspected and maintained in proper working condition with all necessary safety features, including an anti-refire device.

Finally, employers should always display clear warning signs and labels regarding the safe use and handling of nail guns and have an up-to-date safety manual with information about proper use. By implementing safety features, providing proper training and education for operators, regularly inspecting and maintaining the nail guns, and having the necessary safety measures in place, employers can help prevent potential nail gun injuries.

Does the Porter Cable Finish Nailer require oil?

Yes, the Porter Cable Finish Nailer does require regular oil for optimal performance. You should oil your nailer every time you use it. To oil the tool, fill the oil reservoir with a several drops of oil.

Then, stroke the trigger a few times. You will see a few drops of oil coming out of the nailer tip, which is the excess oil being purged from the nailer. This will ensure that oil is getting to the internal components of the nailer.

Be sure to use a good quality air tool oil and not a vegetable-based oil, as this can cause clogging issues.

(Video) Dewalt DXN660 nail gun not firing, pin and driver replaced.

Do all air nailers need oil?

No, not all air nailers need oil. It depends on the specific model you have. If you have a pneumatic air nailer, it may need lubrication in the form of air compressor oil, depending on how frequently the gun is used and what type of nails it is firing.

Some pneumatic guns don’t require oil and use an anvil design that works with the compressed air and the movement of the striking mechanism, preventing the need for oil. On the other hand, electric powered air nailers typically do not require any form of oil or lubricant.

This is because it does not use a mechanical mechanism to fire the nail. It simply uses a trigger activated motor as a power source and is therefore self-lubricating.

Do you need to oil nail gun?

Yes, you do need to oil your nail gun to ensure it continues to work properly. Without proper lubrication, the nail gun can malfunction or break down due to lack of lubrication. To lubricate your nail gun properly, first you need to remove the air filter and nozzle.

Clean the air filter with a cloth to remove any dirt or dust. Once the filter is clean, insert a few drops of oil – either gun oil or silicone spray – into the filter and nozzle. Make sure that the oil is evenly distributed throughout.

Then replace the air filter and nozzle and fire off a few shots to ensure that the oil has distributed itself. You should also lubricate the gun once a month to keep it in working order.

Can I use WD40 on my nail gun?

No, you should not use WD40 on your nail gun. WD40 is a lubricant, which is not suitable for use on a nail gun. WD40 is formulated to displace water and is not a suitable lubricant for the moving parts of a nail gun, as it can cause buildup and attract dirt particles.

It is best to use a specialized lubricant or oil meant for nail gun use, or WD40’s own 3-IN-ONE professional grade oil, which is specifically formulated for use on nail guns. Applying any type of oil to a nail gun can help reduce wear and tear of the internal components over time, but WD40’s low-grade lubricant may not be adequate enough to provide long-term protection.

Where do you put oil in a nail gun?

You should put oil in the chamber of your nail gun where the nails will come out and fire. This is typically located at the bottom of the nail gun, and it is usually labeled or identified by an arrow pointing at it or by the shape or size of the slot itself, which will be larger than the adjacent slots.

To fill the chamber, put two to three drops of oil into the chamber and then check the nails before you start firing them. If there is an air intake valve, make sure to put a few drops of oil there too.

Once the oil is in the chamber, it should be ready for use.

Do you oil a brad nailer?

Yes, you should oil a brad nailer periodically to ensure that it continues to operate properly. Oiling the brad nailer should be done every few months or after about 1,000 nails have been fired. To oil the brad nailer, remove the magazine cap and place two to three drops of oil into the opening.

Reattach the cap and fire two to three empty shots. This ensures that the interior components are properly lubricated. As always, make sure to consult the user manual for any specific instructions related to your particular tool.

How do I make my nail gun deeper?

If you are looking to make your nail gun deeper, it can be done by adjusting the exhaust pressure at the valve cap. The higher the exhaust pressure, the deeper the nail will be driven into the material.

Be careful not to go too high with the pressure though, as it can cause the nail to be forced too deeply and damage whatever you are nailing.

Before adjusting the exhaust pressure, make sure the air pressure is properly adjusted on the compressor to the correct level as recommended by the manufacturer of the nail gun. Many nail guns come with a pressure gauge, so you can easily determine the correct pressure.

Once the air pressure has been adjusted, locate the exhaust pressure setting on the nail gun’s valve and turn the knob to increase the exhaust pressure. Do this slowly and in small increments and test the depth of the nail as you go to make sure it isn’t being driven too deeply.

(Video) Dewalt DCN692 nail gun repair.

When you have reached the desired depth, ensure the safety guard is firmly in place before using the nail gun. With the guard in place, your nail gun should now drive nails at the desired depth.

What is the knob on the back of a nail gun for?

The knob on the back of a nail gun is used to adjust the depth of the nail shooting out from the gun. By adjusting the knob, users can adjust the depth of how far the nail penetrates from the surface it is shooting into.

This is useful to ensure that the nail goes just deep enough not to stick out of the surface, but still deep enough to stay secure. Additionally, it can also be used to adjust the nail size if the nail gun is capable of shooting different sized nails.

Can you change the depth of a nail gun?

Yes, it is possible to change the depth of a nail gun to some extent, although it depends on the type of nail gun you have. Most nail guns have some kind of adjustable depth setting that allows you to control the depth of the nail being fired.

This could involve rotating a dial or switch on the tool, turning a depth setting screw, or adjusting a selector setting. If you have a more sophisticated model, you may also be able to adjust the depth of the nail using a depth stop.

Additionally, some nail guns may have a nozzle that can be adjusted so that you can control the amount of pressure being applied to the nail.

What pressure should a nail gun be set at?

The pressure that a nail gun should be set at will depend on the type of nail gun being used and the type of nails being driven. For example, a framing nailer should typically be set between 70 and 120 psi, while a brad nailer should typically be set between 60 and 100 psi.

It is also important to consider the thickness of the material being nailed when selecting the pressure, as thicker materials may require more pressure to ensure the nail has driven into the material properly.

Additionally, the power of the nail gun can play a role in selecting the pressure; typically, a more powerful nail gun will require lower pressure to drive in the nails. Ultimately, it is important to refer to the instruction manual of both the nail gun and the nails to determine the correct pressure to use.

What PSI should I use for trim?

When selecting the appropriate PSI for trim or finish work on walls, the general rule of thumb is to use the lowest PSI settings your spray gun allows. Finish work requires detailed coverage and too much pressure can cause the material to splatter or puddle.

A good rule of thumb is to start at around 15 PSI and adjust from there as needed. An adjustable spray gun gives you more flexibility to adjust the PSI to fit the type of job you’re working on, as well as the specific material being painted.

It’s also important to make sure the compressor you are using can support the pressure setting you select. If the PSI is too low, the spray gun will draw too much material, causing the finish to be too heavy.

Too much PSI might prevent the material from atomizing properly, resulting in an uneven cover. It is also important to wear safety equipment when using a spray gun at all times, as it creates fine particles which, when inhaled, can be hazardous.

How do you use a nail gun for beginners?

Using a nail gun for the first time can be daunting, but with a little practice, it can become a useful skill! To use a nail gun for beginners, first make sure you understand the safety protocols and guidelines associated with the nail gun.

Ensure you are wearing the proper eye and hearing protection, as well as gloves, to protect yourself while using the nail gun. After you have put on your safety gear, it is time to load the nail gun with nails and secure it to the surface.

Place the nail gun on the surface and firmly press the tip against the surface, then, turn on the machine and pull the trigger when ready to shoot. It is important to be sure that you are aiming straight and in the desired spot when firing the nails.

Keep your hold secure and repeat the process as desired. After you have finished, turn off the machine and be sure to safely store the nails and device. With proper care and maintenance, your nail gun can be a great addition to many projects and continue to be reliable for a long time.

(Video) Dewalt dcn660 won't fire


1. DeWalt Cordless Framing Nail Gun Troubleshooting
(Tom Brueggen)
2. How to fix Dewalt D51238 nail gun
3. How to fix DEWALT DC608 DCN680 DCN681 missfiring
(Dominguez Renovations)
4. DCN692 Not Sinking Nails? Don't Know Why? I Don't Either!!
(Doctor Lefthandthread)
5. Dewalt brushless DCN660 Nailer stops after month? Lose part inside! Handyman
6. How to fix a Dewalt DCN660 nail gun that won't fire nails, trigger not working.
(Dean Doherty)
Top Articles
Latest Posts
Article information

Author: Greg Kuvalis

Last Updated: 03/20/2023

Views: 5718

Rating: 4.4 / 5 (75 voted)

Reviews: 90% of readers found this page helpful

Author information

Name: Greg Kuvalis

Birthday: 1996-12-20

Address: 53157 Trantow Inlet, Townemouth, FL 92564-0267

Phone: +68218650356656

Job: IT Representative

Hobby: Knitting, Amateur radio, Skiing, Running, Mountain biking, Slacklining, Electronics

Introduction: My name is Greg Kuvalis, I am a witty, spotless, beautiful, charming, delightful, thankful, beautiful person who loves writing and wants to share my knowledge and understanding with you.